AIDA Imaging IPCOMM-POE – Portable Video & Control Wireless Transmitter

$275.00

In stock

AIDA Imaging IPCOMM-POE - Portable Video & Control Wireless Transmitter $275.00
  • Free US shipping on all orders over $200
  • 30 day returns (restock fee applies for some items)
  • In stock items ship next business day
Guaranteed Safe Checkout

With the power to inject PoE+ power into any camera via DC12V or a NPF-Battery (not included), you can easily take your video creations wirelessly onto any Wi-Fi router, sending IP video or IP control flawlessly as far as your router can reach!

This solution brings a whole new level of broadcasting opportunity for on-the-go, non-mounting solutions! So bring on this revolution, and start streaming wireless today!

Connect to any Wi-Fi router with EASE!

Its as easy as locally connecting your IPCOMM-POE to your computer, connecting to the Wi-Fi router, and following the steps to get wireless transmission started!

Bringing Power to a Camera near you!

With the ability to use the DC12V or NPF type battery (sold separately,) you can supply beloved PoE+ power to your camera, simultaneously powering and sending video and control over the network!

Multiband-lingual kind of device…

With the power to connect to a 2.4GHz or 5GHz Wi-Fi router, the IPCOMM-POE has you covered on almost any router out on the field or market!

Unlimited Potential

With a mobile setup, you bring any IP camera power, video transmission, and control over a wireless network. With nothing holding the camera down, this brings unlimited potential to any streaming solution you can think of at a GREAT price!

Housing BUILT to last

With AIDA’s special hardened aluminum housing formula, you can expect your IPCOMM-POE to perform when, and where you need it most!

Kbps based, not resolution!

With the ability to send up to 50Mbps MAX, you can send fluid 720 to 4K video with ease over your network! Some things to note to achieve this <10ms ideal scenario:

  1. Limit the amount of obstacles between the router and IPCOMM-POE
  2. Ensure the signal strength seen when setting the IPCOMM-POE up is above 60%
  3. Ensure the bandwidth sent by the camera to the router is within 2Mbps~50Mbps, this mostly depends on your signal strength. Anything higher will cause delay and video rupturing.
  4. Using the SRT protocol (Found on all AIDA IP cameras) can drastically help video tearing for further distance / lower bitrate video, however it comes at the price of a little more latency.

Specifications

Transmission

Antennas: 4 x 3dBi Dual Band Omni-Directional
Wireless Standard: IEEE802.11ac/a/b/g/n
Transmission Rate: Up to 80 Mbps
RF Parameters: Receiver Sensitivity: -96dBm Freq: 2.412~2.472GHz 5.180~5.725GHz
Channel Bandwidth 20/40/80 MHz, AUTO
Encryption: WPA-PSK / WPA2-PSK / WPA/WPA2

Physical

Physical Ports: RJ45 Port, 12VDC port, NPF Battery Slot
Case: Hardened Aluminum
PoE+ Port Standard: Up to IEEE 802.3at
Indicators: PWR, PoE+ and NPF Battery Status
Switch: On and Off
Operating Temp: 0°C ~ 55°C
Dimensions: Without antennas: 4.49″ x 1.3″ x 3.66″ (144mm x 33mm x 93mm), With antennas: 10.04″ x 4.14″ x 4.5″ (255mm x 105mm x 114mm)

Additional information

Brand

AIDA Imaging

Reviews

There are no reviews yet.

Be the first to review “AIDA Imaging IPCOMM-POE – Portable Video & Control Wireless Transmitter”